Our commitment
Three Layers of Assurance on Every Project
We follow the professional standards, technical guidelines and statutory requirements that apply to each project's scope.
Registered Professionals
Geological reports are signed off by Professional Geologists under the Geologists Act 2008. Engineering design is signed by BEM-registered Professional Engineers.
Recognised Standards
Investigation and testing follow BS 5930, MS EN 1997 (Eurocode 7), ASTM methods and JKR slope guidelines, as the scope requires.
Statutory Compliance
Fieldwork meets DOSH, CAAM and environmental requirements, with documents ready for authority and client audit.
Standards & compliance
The Standards and Frameworks We Work To
Which standard applies depends on the project scope, the authority and the discipline. Here is where each one is typically used.
Professional & Technical Standards

Code of practice for ground investigations

Geotechnical design principles

Slope investigation, assessment and design

SPT, crosshole seismic and resistivity test methods
Statutory & Regulatory Frameworks

Professional practice and registration requirements

Construction site safety and occupational health

Environmental and EIA requirements, where applicable

Drone flight permits and compliant flight operations
Registrations
Registered and Ready for Procurement
Certificates are available for vendor registration and tender submissions.
CIDB Registration
Construction Industry Development Board registration.
Ministry of Finance (MOF)
Registered supplier for government procurement.
Registered Professional Geologists
Geological reports signed off by P.Geol. registered with the Board of Geologists Malaysia under Act 689.
Professional Engineers (Ir.)
Engineering design and certification by Professional Engineers registered with BEM.
Professional Geospatialists (Gs.)
Geospatial work led by Professional Geospatialists recognised by IGRSM.
DOE-Registered Subject Matter Expert
Environmental input from a Subject Matter Expert registered with the Department of Environment.
Our method
How Standards Map to Each Service
What each method detects, how deep it reaches, and the standard behind it.
| Service | Detects | Depth range | Standard | Deliverables |
|---|---|---|---|---|
| MASW | VS30, velocity, site class, shear-wave | 15 – 30 m | ASTM D4428 · MS EN 1997 | Vs profile, seismic class |
| Soil Investigation (Borehole + SPT) | N-value, strata profile, groundwater | 10 – 60 m | BS 5930 · ASTM D1586 | Borelogs, SI report, lab results |
| Electrical Resistivity Imaging | Water, bedrock, cavities, contamination | 20 – 150 m | ASTM D6431 | 2D / 3D resistivity |
| LiDAR & Aerial Photogrammetry | Terrain, volumes, slope geometry | Surface | CAAM-compliant flight operations | DTM, DSM, contours, volumetrics |
| Slope Hazard Assessment | Failure mode, factor of safety | Site-wide | JKR Slope Guidelines | Hazard rating, remedial options |
| Geoforensics Investigation | Cause of failure, settlement cause | Case-dependent | Expert witness guidance · Act 689 | Forensic report, testimony report |
Quality assurance
How Compliance Is Built Into Every Project
Five checks from the first scope review to the final signature.
1
Scope Review
Check authority, client and project specifications before fieldwork.
2
Method Statement & HIRARC
Risk assessment and a safe work plan for every site.
3
Field QA/QC
Calibrated equipment, logged procedures and chain of custody.
4
Lab Testing
Samples tested to recognised standards.
5
Review & Sign-off
Internal review, then endorsement by a P.Geol. or Ir.
Need our compliance documents for a tender?
We'll send our company profile and the certificates you need.
Frequently Asked Questions
Professional geological work must be carried out by a Professional Geologist (P.Geol.) registered under the Geologists Act 2008 (Act 689). Geotechnical engineering design and certification may also require a Professional Engineer (Ir.) registered with BEM.
Soil investigation follows BS 5930, with SPT to ASTM D1586 and geotechnical design parameters aligned to MS EN 1997 (Eurocode 7), plus any project or authority specification.
Yes. Slope investigation, hazard assessment and design follow JKR slope design guidelines where they apply to the project and authority.
Our geophysical testing references ASTM methods, including ASTM D4428 for crosshole seismic testing and ASTM D6431 for resistivity surveys, as the project requires.
Yes. Drone operations are planned and flown under Civil Aviation Authority of Malaysia requirements, with the permits each site needs.
All fieldwork follows DOSH and OSH requirements under the Occupational Safety and Health Act 1994, with a risk assessment and safe work plan for every site.
Yes. Geotechnica Sdn Bhd is CIDB and MOF registered. Certificates are available on request for vendor registration and tenders.
Yes. Email admin@geotechnica.com.my and we will send our company profile and the certificates your tender needs.
Work with us
Need Reports That Stand Up to Authority Review?
Tell us about your project, authority and submission requirements. We’ll scope an investigation that meets them from day one.